Echobox D7 emulates an echo tape mode found in a particular Japanese stomp-box which itself was a digital remake of a famous American tape echo.

• Delay Time – adjusts, well, delay time (overall range is 30 – 2600 ms).
• Repeat – adjusts amount of feedback (values above 5 result in (self-)oscillation).
• Delay Level – sets the volume of delays that gets mixed with dry signal (not wet/dry ratio!).
• Range – sets the delay time range in which the Delay Time knob operates (30-160, 120-650, 480-2600 ms).
• Mute – “true” bypass in the sense that it also clears the delay buffer, so you get the behavior as with regular stomp-box (i.e. no weird echos that remain in buffer and return right after switching the effect on again as is the rather common case with time based plug-ins, regular DAW bypass however exhibits this awkward behavior).
• Manual BPM sync – a set of six “kick” buttons and one three-way switch that allow quick setting of musically relevant delay times relative to actual project tempo.

senderspike

EchoboxD7  ( 0.7 MB )

EchoboxD7_x64  ( 0.7 MB )

Modul 8 is a dual LFO stereo chorus.

• Two independent LFOs with on/off switches and adjustable speed and width (LFO A oscillates at 0.8 Hz to 8 Hz, and LFO B oscillates at 0.3 Hz to 3 Hz).
• Feedback control that sets the amount of flanging.
• Optional filtering and adjustable drive of modulated signal.
• Phase invert on R channel for wide stereo (mono incompatible).
• LFO mute “kill-switch” for musical phrasing.
• Separate wet and dry controls.

https://senderspike.wordpress.com/

Modul8  ( 0.7 MB )

Modul8_x64  ( 0.7 MB )

SN06-G is a model of an operational amplifier, inspired by the drive section which can be found in famous American modular synthesizers and stomp-boxes

• Drive gain -8 dB to +24 dB.
• Input attenuation (-10 dB).
• Input boost (+10 dB).

https://senderspike.wordpress.com/

SN06G-OpAmp  ( 0.5 MB )

SN06G-OpAmp_x64  ( 0.5 MB )

SN05-G is a brickwall (sample peak) limiter.
It is best suited for the very end of the signal chain, but can easily handle also individual tracks.

• Input gain 0-24dB.
• Ceiling 0dBFS to -24dBFS.
• Release time from 0.1ms to 20ms.
• Fixed attack time.
• GR meter.

https://senderspike.wordpress.com/

SN05G-Limiter  ( 0.6 MB )

SN05G-Limiter_x64 ( 0.6 MB )

SN04-G is a hybrid character 3-band channel EQ.
It comes with basic surgical capabilities, LP/HP section, adjustable output volume and phase, and optional “analog modeling”. It’s designed with ASIO/CPU footprint that allows it to live across all channels of a project as a virtual console EQ.

• HF: +/-18dB shelf or bell filter with variable bandwidth and 7 switchable frequencies.
• MF: +/-18dB bell filter with variable bandwidth and 7 switchable frequencies.
• LF: +/-18dB shelf or bell filter with variable bandwidth and 7 switchable frequencies.
• HPF: slope of 6dB, 12dB, 18dB, and 24dB per octave, with 5 switchable frequencies.
• LPF: slope of 6dB, 12dB, 18dB, and 24dB per octave, with 5 switchable frequencies.
• Bell filter bandwidth proportional to gain and frequency.
• Symmetrical and asymmetrical modes for boost/cut (bell filter only).
• “American” and “British” shelving modes.
• Output gain +/- 25dB.
• Phase invert at output.
• Optional rudimentary “analog modeling”.

https://senderspike.wordpress.com/

SN04G-Channel-EQ  ( 0.8 MB )

SN04G-Channel-EQ_x64  ( 0.9 MB )

• Input gain +/- 24dB.
• Output gain +/- 24dB.
• NAB, IEC (15 IPS), AES (30 IPS) EQ modes.
• Adjustable recording EQ (LF +/- 10dB, HF +/- 14dB).
• Adjustable reproduction EQ (LF +/- 10dB, HF +/- 14dB).
• Adjustable “head bump” frequency from 65Hz to 105Hz.
• Adjustable “head bump” gain from 1dB to 8dB.
• Tape hiss gain +/-30dB from ca. -76dBFS (RMS).
• Tape hiss on/off switch.
• Complete I/O VU metering.
• …and tape saturation, of course.

https://senderspike.wordpress.com/

SN03  ( 0.6 MB )

SN03_x64  ( 0.7 MB )